Home > SuperSprings > Mazda

Free Shipping on All SuperSprings Suspension Kits!

Some kits require a Mounting Kit (MTKT). If required you will be given the option to add once you click on the Kit# so take note if your application requires the Mounting Kit MTKT.

Application
Years
Kit #
MTKT Required
Capacity
Special Instructions
B Series Pickup - Regular Loading
94-08 SSA5 YES 2000
B Series Pickup - Heavy Loading
94-08 SSA8 YES 3000
Sort By:
Page of 2
SSA1 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 38" Long x 2.5" Wide x .323 gauge
  • 800 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $269.99
SSA10 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 52" Long x 3" Wide x .558 gauge
  • 1500 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $319.99
SSA11 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 40" Long x 3" Wide x .447 gauge
  • 1650 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $369.99
SSA12 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 42" Long x 3" Wide x .558 gauge
  • 1900 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $349.99
SSA13 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 49" Long x 3" Wide x .946 gauge
  • 3000 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $399.99
SSA14 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 47" Long x 3" Wide x .447 gauge
  • 1350 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $279.99
SSA15 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 55" Long x 3" Wide x .946 gauge
  • 2600 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $359.99
SSA16 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 47" Long x 3" Wide x .499 gauge
  • 1650 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $309.99
SSA17 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 44" Long x 3" Wide x 1.116 gauge
  • 4400 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $469.99
SSA18 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 45" Long x 3" Wide x .360 gauge
  • 950 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $279.99
SSA19 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 40" Long x 2.5" Wide x .401 gauge
  • 850 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $279.99
SSA2 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 40" Long x 2.5" Wide x .323 gauge
  • 750 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $249.99
SSA20 SuperSprings Helper Spring Nissan Titan

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 47" Long x 3" Wide x .447 gauge
  • 1350 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $389.99
SSA22 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 43" Long x 3" Wide x .558 gauge
  • 2200 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $399.99
SSA23 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 49" Long x 3" Wide x .558 gauge
  • 2000 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $419.99
SSA24 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 51" Long x 3" Wide x 1.116 gauge
  • 4000 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $509.99
SSA24.5 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 51" Long x 3" Wide x 1.116 gauge
  • 2000 Pounds Rating Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $258.30
SSA25 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 43" Long x 3" Wide x .625 gauge
  • 3300 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $469.99
SSA28 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 42" Long x 3" Wide x .558 gauge
  • 1500 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $329.99
SSA29 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 31" Long x 2.5" Wide x .401 gauge
  • 950 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $249.99
SSA3 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 40" Long x 2.5" Wide x .360 gauge
  • 850 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $249.99
SSA30 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 44" Long x 3" Wide x .360 gauge
  • 950 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $289.99
SSA31 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 44" Long x 3" Wide x .447 gauge
  • 1500 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $329.99
SSA34 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 42" Long x 3" Wide x .558 gauge
  • 1900 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $389.99
SSA36 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 40" Long x 2.5" Wide x .323 gauge
  • 750 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $279.99
SSA4 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 40" Long x 2.5" Wide x .401 gauge
  • 1100 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $369.99
SSA5 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 44" Long x 3" Wide x .360 gauge
  • 950 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $249.99
SSA6 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 47" Long x 2.5" Wide x .401 gauge
  • 900 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $249.99
SSA7 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 40" Long x 2.5" Wide x .401 gauge
  • 1100 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $299.99
SSA8 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 44" Long x 3" Wide x .447 gauge
  • 1500 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $299.99