Home > SuperSprings > Nissan

Free Shipping on All SuperSprings Suspension Kits!

Some kits require a Mounting Kit (MTKT). If required you will be given the option to add once you click on the Kit# so take note if your application requires the Mounting Kit MTKT.

Application
Years
Kit #
MTKT Required
Capacity
Special Instructions
Pickup
86-97 SSA2 NO 1800
Frontier 2x4 - Regular Loading
98-04 SSA2 NO 1800
Frontier 2x4 - Heavy Loading
98-04 SSA7 NO 3000
Frontier 4x4 - Regular Loading
98-04 SSA2 YES 2000
Frontier 4x4 - Heavy Loading
98-04 SSA7 YES 3000
Frontier 2x4,4x4
05-10 SSA1 YES 2000
Square shackle upper bolt hole rear / Trim bumpstop
Xterra
00-07 SSA1 NO 2000
Titan
04-10 SSA20 NO 3000
Includes special mounting kit
UD LCF 1200,1300,1400,1800 Series
00-10 SSA22 NO 5000
Sort By:
Page of 2
SSA1 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 38" Long x 2.5" Wide x .323 gauge
  • 800 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $249.99
SSA10 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 52" Long x 3" Wide x .558 gauge
  • 1500 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $319.99
SSA11 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 40" Long x 3" Wide x .447 gauge
  • 1650 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $369.99
SSA12 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 42" Long x 3" Wide x .558 gauge
  • 1900 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $349.99
SSA13 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 49" Long x 3" Wide x .946 gauge
  • 3000 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $399.99
SSA14 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 47" Long x 3" Wide x .447 gauge
  • 1350 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $279.99
SSA15 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 55" Long x 3" Wide x .946 gauge
  • 2600 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $359.99
SSA16 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 47" Long x 3" Wide x .499 gauge
  • 1650 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $309.99
SSA17 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 44" Long x 3" Wide x 1.116 gauge
  • 4400 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $469.99
SSA18 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 45" Long x 3" Wide x .360 gauge
  • 950 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $279.99
SSA19 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 40" Long x 2.5" Wide x .401 gauge
  • 850 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $279.99
SSA2 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 40" Long x 2.5" Wide x .323 gauge
  • 750 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $249.99
SSA20 SuperSprings Helper Spring Nissan Titan

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 47" Long x 3" Wide x .447 gauge
  • 1350 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $389.99
SSA22 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 43" Long x 3" Wide x .558 gauge
  • 2200 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $399.99
SSA23 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 49" Long x 3" Wide x .558 gauge
  • 2000 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $419.99
SSA24 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 51" Long x 3" Wide x 1.116 gauge
  • 4000 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $509.99
SSA24.5 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 51" Long x 3" Wide x 1.116 gauge
  • 2000 Pounds Rating Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $258.30
SSA25 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 43" Long x 3" Wide x .625 gauge
  • 3300 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $439.99
SSA28 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 42" Long x 3" Wide x .558 gauge
  • 1500 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $299.99
SSA29 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 31" Long x 2.5" Wide x .401 gauge
  • 950 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $249.99
SSA3 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 40" Long x 2.5" Wide x .360 gauge
  • 850 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $249.99
SSA30 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 44" Long x 3" Wide x .360 gauge
  • 950 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $289.99
SSA31 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 44" Long x 3" Wide x .447 gauge
  • 1500 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $329.99
SSA36 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 40" Long x 2.5" Wide x .323 gauge
  • 750 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $279.99
SSA4 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 40" Long x 2.5" Wide x .401 gauge
  • 1100 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $369.99
SSA5 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 44" Long x 3" Wide x .360 gauge
  • 950 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $249.99
SSA6 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 47" Long x 2.5" Wide x .401 gauge
  • 900 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $249.99
SSA7 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 40" Long x 2.5" Wide x .401 gauge
  • 1100 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $299.99
SSA8 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 44" Long x 3" Wide x .447 gauge
  • 1500 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $299.99
SSA9 SuperSprings Helper Spring

SuperSprings Self-Adjusting Suspension Stabilizers work with your current suspension to reduce sway and increase load capacity while never needing any adjustments due to the roller design.

  • Increase Load and Tow Capacity without Increasing Ride Stiffness
  • Reduce Sway - Independently tested to give 29% improvement in driver control
  • Maintenance Free and No Adjustments Needed
  • Easy to Install - Most Kits Install in Less than 30 Minutes
  • Limited Lifetime Warranty
  • Sold as Kit - Order 1 per Vehicle
  • Free Shipping to Continental U.S.
  • Dimension - 47" Long x 3" Wide x .447 gauge
  • 1300 Pounds Spring Capacity Increase

SuperSprings are progressive in nature in that they work on an as-needed basis. The installed springs are under nominal tension even when the vehicle is unloaded. This is so there is no rattle or noise and the patented rollers will activate automatically.

As a vehicle with rear leaf springs comes under load the factory springs react as they are designed to. The center of the springs move vertically causing the overall leaves to flex and flatten out. This movement in the factory spring activates the SuperSpring through the rollers at the end of each leaf. Because the SuperSpring rollers aSupersprings Shacklere under tension, a movement in the factory spring causes them to move, seeking their new point of least resistance. This simple roller principal allows the SuperSprings to activate and deactivate automatically, free of any manual adjustment.

The SuperSprings are length specific to fit varying sized leaf springs. In addition the different lengths typically are manufactured in light, medium and heavy duty strengths. The sole adjustment on the SuperSprings is found in the roller shackles at the end of each leaf. The typical shackle has two bolt holes, as shown in the diagram below though some single hole and three holed shackles are used. The most common installation involves positioning all four rollers in the lower (furthest from the eye of the SuperSpring / closest to the ground) bolt holes. This ensures the least amount of preload tension on the SuperSprings and keeps the vehicle closest to its original factory ride conditions. Upper bolt holes may be used if additional lift is desired in the vehicle; if clearance from obstructions is required or if the installation is on an older vehicle with some fatigue in the springs.

SuperSprings enhance load carrying capacity, handling and towing. Do not load any vehicle beyond the manufacturers gross vehicle weight rating.

Our Price: $299.99
   
 

Helper Springs for Nissan Trucks

From hauling tools and towing equipment to everyday driving over thousands of miles of road, as your truck gets older, one of the first things to wear down is the suspension system. When you notice your vehicle is swaying from side to side, dipping lower to the ground or can’t carry as heavy a load as it used to, helper springs can correct the problem and extend the life of your vehicles.

Whether you’re looking for Nissan Titan overload springs to upgrade your suspension for a heavy-duty application or Nissan Xterra helper springs to ensure your aging ride continues to operate safely, General Spring has a solution in stock. Browse our online inventory to find the product that fits your needs, or give us a call at 1-888-829-0619 to speak to a knowledgeable sales representative.

Complete Selection of Nissan Frontier Overload Springs and SuperSprings for All Types of Trucks

General Spring offers SuperSprings as an innovative product capable of stabilizing your suspension system to level loads and reduce body roll. Whether you’re in the market for Nissan Frontier helper springs, Nissan Titan helper springs or a kit for any other model, you’re getting a self-adjusting solution that’s different and more effective than an add-a-leaf or air bag. These overload springs are simple to install for do-it-yourself mechanics of any level, manufactured with high-grade steel and feature a smart design that never results in a stiffer ride.

Within our inventory, you’ll find Nissan overload springs in a wide range of models, years, applications and capacities. SuperSprings helper springs are designed to fit directly on leaf springs of all different sizes, and once installed, they will automatically adjust to work in sync with your suspension. If you have an older model truck or a special application, let us know, and we’ll help you find a solution suited to your specific requirements.

Your Reliable Source for Nissan Truck Helper Springs

As your leaf springs and suspension authority since 1965, General Spring takes pride in carrying aftermarket products that solve your problems fast and efficiently. Purchasing Nissan Frontier helper springs from us is a cost effective way to fix your old truck, complete a restoration project or prepare a vehicle for a rugged work environment. We offer competitive prices on high-quality products and will ship helper springs for free to locations throughout the U.S.

Additional benefits of partnering with us for your suspension needs include:

  • Convenient online shopping experience with the ability to speak to a live representative
  • Expert assistance selecting the right products for your vehicle
  • One-year warranty on quality tested Nissan overload springs
  • Safe and secure checkout and registered customer accounts

When you’re searching for regular loading Nissan Xterra overload springs, heavy loading Nissan Titan helper springs or any other type of SuperSprings suspension kits, we have what you need in stock. Give General Spring a call to speak to a knowledgeable representative or contact us online for assistance with placing your order today.